PC - Windows
PC - Windows
Cheat Codes Club
A Cheat Codes
Game Name : Prince of Persia 3D
System : PC - Windows
Date Added : 2004-08-17 12:34:47
Views : 15661
Edit the shortcut for Prince of Persia 3D and add '-console' to the end of the 'Target' field so that it reads as follows:
"D:\Program Files\Red Orb\Prince of Persia 3D\POP3D.exe" -CONSOLE
When you start using this new shortcut, press [F5] to open the console. Enter one fo the following codes in the console to enable the cheat:
IMMORTAL = God Mode
MORTAL = leave God Mode
VERSION = show the version number of your game (should be 1.1)
NEXTLEVEL = instantly skip to the next level
FLYCAM = enable flying camera. type again to turn off.
Note: These cheats will only work with the v1.1 patch.
Magic Trainer Creator Cheat
As the game moves the address for health to different places, a search can be done for a specific string which indicates the health value. Set the beginning address to 3000000 and the ending adress to 4000000. Search for 000000240000000000000003 if the prince has 3 full bottles of elixir. The hex 24 in the string can be set to a maximum of hex 76, which gives the prince 10 full bottles of elixir. This 76 should now be frozen by Magic Trainer Creator so that the next time it is played, it will be known what string to search for, e.g.
However, for some reason, this doesn't always work.
Save Game Hex Cheats
Saved games are the files named SAVE001, SAVE002, SAVE003, etc. in the directory the game was installed into (C:\POP3D, for instance). Using a hex editor, the following game values may be adjusted.
First search for the all lower-case word "buffer". It will be at the end of a long string of paths containing the word geometry. Now count 330 more bytes from the end of "buffer". This location contains the amount of health the prince currently has. The maximum value this may be set to is hex 76. Count four more bytes and this location contains the maximum amount of health the prince *may* have. This maximum value is also hex 76.
262 bytes past the end of "buffer" are the two bytes that enable the three bladed weapons and six types of arrows. Hex 1F 1F enables everything.
238 bytes from the end of "buffer" contains the number of type 1 arrows the prince has. The maximum value this may be set to is hex FF (255). The display for the number of arrows will not show correctly on the game screen for values greater than 99.
4 bytes further contains the value for type 2 arrows. Max is hex FF.
4 bytes further is type 3 arrows. Max is hex FF.
4 bytes further is type 4 arrows. Max is hex FF.
4 bytes further is type 5 arrows. Max is hex FF.
4 bytes further is type 6 arrows. Max is hex FF.
Sometimes the first of the six values for arrows starts 222 bytes past the end of "buffer" instead of 238 bytes past "buffer". Then the type 2 arrows are at 238, type 3 four bytes from there, and so on.
Load the game with one of the following command lines, then select "New Game" to start at the corresponding level. Note: The game cannot be completed normally once this method is used. Each level must be loaded with the same method to continue or else the game will load level two after the current level is completed.
pop3d.exe -l "geometry\rooms\prisonfix"
pop3d.exe -l "geometry\rooms\ivorytwr"
pop3d.exe -l "geometry\rooms\cistern"
pop3d.exe -l "geometry\rooms\palace2"
pop3d.exe -l "geometry\rooms\palace3"
pop3d.exe -l "geometry\rooms\palace4"
pop3d.exe -l "geometry\rooms\roof1"
pop3d.exe -l "geometry\rooms\cityanddocks"
pop3d.exe -l "geometry\rooms\dirig1a"
pop3d.exe -l "geometry\rooms\dirig1b"
pop3d.exe -l "geometry\rooms\dirig2"
pop3d.exe -l "geometry\rooms\dirigfinale"
pop3d.exe -l "geometry\rooms\ruins"
pop3d.exe -l "geometry\rooms\cliffs"
pop3d.exe -l "geometry\rooms\solar1"
pop3d.exe -l "geometry\rooms\moontemple"
pop3d.exe -l "geometry\rooms\finale"
Not enough codes for you? Search for more cheats at cheat codes club.
Or simply Click here to find more Prince of Persia 3D cheat codes.
Copyright © 2001 - 2018 Cheat Patch. All Rights Reserved